http://www.duanebeins.com/screw-kit-set/
Installation Instruction for Hid Conversion Kits
HID Conversion Kits might be illegal in some states and are sold for off road or show use only. Check with your local BMV for more information.
Helpful Information and Installation Tips:
- Do not touch the HID bulb. If you do touch the bulb during installation, clean with alcohol.
- Do not look directly into the bulb when it is turned on as it may cause permanent damage to your eyes.
- Headlights must be properly adjusted after installation. HID bulbs are much brighter than halogen bulbs. By not adjusting your headlights, you may reduce the visibility of oncoming traffic due to glare. If you do not know how to adjust your headlights, please consult a professional.
- Do not drop or apply inappropriate/unnecessary force to your HID components as doing so may cause damage to them. If any damage is discovered, discontinue use and contact your retailer. Do not use the system until the problem is solved, in order to avoid possible electric-shock or fire.
- The HID system generates 23000volts when activated. Do not use wet or oily hands when installing or inspecting the system. Or you may be subjected to severe burns or electric-shock.
- Make sure all connectors and wires are secured and away from any hot surfaces. Wires that are loose or resting against a hot surface may cause electrical hazards.
- Do not turn on the bulb near flammable material when it is outside of headlight housing.
- Do not turn lights on/off rapidly. Doing so may reduce the lifespan of your bulbs.
- Do not install HID system in any housing with cracks. Moister may damage the bulb or cause electric-shock.
- Before final installation pre-test all the components. Ensure compatibility by plugging in all the wires and turning the system on.
Note: Special adapters, connectors, modules or harness may be needed to correctly install the HID system on some vehicles. Make sure you have everything needed for your vehicle. BMW, Mercedes, Audi, Dodge/Chrysler and Volkswagen are only a few that may need special installation materials.
Single Beam Installation Instructions:
- Verify that the HID Conversion Kit you received have all the component needed for the installation (A list of component available below)
- Disconnect the car battery.
- Remove the factory light bulbs. If your vehicle’s headlights have dust caps, please remove them as well.
- If your vehicle is equipped with headlight dust caps, drill a 1″(24mm) hole to accommodate the wiring harness.
- Remove the xenon HID bulb from the protective casing. Be careful NOT to touch the bulb. Handle it by its plastic base. If any grease or dirt gets on the bulb wipe clean with rubbing alcohol.
- Put the bulb’s wiring harness through the dust cap (as illustrated).
- Insert the xenon HID bulb into your headlight and secure it.
- Connect the spade terminals (positive & negative) to the factory headlight wiring harness.
- Insert the rubber boot (on the wiring harness) through the hole on the dust cap (which you drilled earlier).
- Connect the bulb to the ballast. The quick release will “click” once fully secured.
- Find a mounting location for the ballast. Use the ballast bracket, screws or zip-ties as needed. Note: Do not drill holes on the ballast box, mount away from moving components and mount to a secure location.
- Check your vehicle’s headlight fuse. Make sure it is rated at 20amps or higher. Replace the fuse with a 20amp fuse if your headlight fuse is of a lower rating.
- Reconnect the battery cables.
- Turn light switch on and allow your new xenon light to run for 10 minutes.
Bi-Xenon Installation Instructions:
Wiring Diagram
- Verify that the HID Conversion Kit you received have all the component needed for the installation (A list of component available below)
- Clean all connectors and wipe the HID bulbs and connectors with rubbing alcohol
- Install the HID bulbs into the headlight housing
- Connect the HID bulbs to the ballast (2 round quick-disconnects)
- Connect the high beam control wires (small rectangular connectors)
- Connect the ballasts to the Hi/Lo wiring harness (oval connectors with yellow rubber seals)
- Connect the 3-pin socket on the wiring harness to ONE of the headlight sockets
- Connect the thick red wire to the battery positive
- Connect the thick black wires to the battery negative or ground
- Mount the ballast and clean up the wiring harness with zip ties
- Find a mounting location for the ballast. Use the ballast bracket, screws or zip-ties as needed. Note: Do not drill holes on the ballast box, mount away from moving components and mount to a secure location.
- Turn headlight switch on and allow your new xenon light to run for 10 minutes
Adjusting Your Low Beam Headlight:
- Park on a level surface 20 feet behind another car and turn on your low beam headlights.
- Make sure the cut-off of the beam is just above the bumper of the car in front. (Please refer to the image below)
- To make sure the two headlights are even adjusted, please turn on the headlights directly against a flat wall 20 feet away and adjust lights until the cut-offs of two headlight line up.
Troubleshooting:
Flickering during pre-test or bulb out warning: Some vehicles measure the resistance of the bulb connecting into the factory socket. Since the Xenon ballast does not use any resistance when lighting the bulbs, the vehicles computer thinks there is something wrong, when there really is not. It will then begin to flicker the HID kit and may display a bulb out warning. To remedy this, an automotive HID bulb out resistor must be used, or a bulb out warning module.
Single Beam HID Conversion Kit Components:
- HID Xenon Bulbs (with wires) Two (2) pieces
- HID Ballasts Two (2) pieces
- Bracket(s)/Screw(s)/Other Mounting Accessories One (1) set
- Installation Manual One (1) piece
Bi-Xenon HID Conversion Kit Components:
- HID Xenon Bi-Xenon Bulbs (with wires) Two (2) pieces
- HID Ballasts Two (2) pieces
- Hi/Low Beam Control Wiring Harness One (1) piece
- Bracket(s)/Screw(s)/Other Mounting Accessories One (1) set
- Installation Manual One (1) piece
***Some items may vary from one manufacturer to another***
This Installation guide is written for the HID Conversion Kits listed above. Some kits might require additional steps that are not listed here. Contact your supplier for more information.
About the Author
We provide the best quality
HID conversion kits in the US. Made in China with the latest German
Technology 9004, 9005,
9006,
9007, H1, H4 and
H7
Button/Screw/Pinhole Camera Set
|
|
New Screw Kit Screws Set for IBM Thinkpad T40 T40p T41 T41p T42 T42p T43 T43p $4.99 |
|
|
Lenovo IBM Thinkapd New Screw Kit Screws Set T60 T60p $5.50 |
|
|
Zojirushi SL-JAE14 Mr. Bento Stainless Steel Lunch Jar $45.99 Zojirushi’s Mr. Bento Stainless Lunch Jar in Silver is unique and functional. Stainless steel construction and vacuum insulation. Four microwaveable inner bowls and washable container. Includes a convenient carry strap for easy transport and a easy to carry bag…. |
|
|
Mr. Beer Deluxe Edition Home Microbrewery System $28.12 In just 14 days, beginning and advanced brewers alike can enjoy a glass of premium, handcrafted beer with this home-brewing kit. The 2-1/2-gallon brewing keg features a pour tap and wide-mouth lid for easy cleaning by hand. Included with this starter kit are a can of West Coast Pale Ale mix, which produces twenty 12-ounce bottles of mild, full-bodied beer, and a single-use packet of booster, … |
|
|
Metrokane Rabbit Wine Opener Tool Kit, Silver $45.00 This 6-Piece Rabbit Corkscrew Tool Kit includes not only the award-winning Silver Metrokane Rabbit Wine Opener (Model 6005), but you will also receive a Foil Cutter, Drip-Stop Ring, Wine Bottle Stopper / Sealer, Wax Whacker and Extra Replacement Worm. The Metrokane Rabbit Corkscrew is faster than a speeding bunny. The Rabbit pulls a cork in 3 seconds flat, and then automatically releases the cork… |
|
|
Merkur Model 180 Long Handled Safety Razor $28.00 Merkur Long Handled Safety Razor-#180- Made in Germany * An Extra Close Shave! * Merkur High Quality Shaving * Chrome Finish Sturdy Razor * Long Handle – great for people with large hands * Made in Germany The Merkur Long Handled Safety Razor has a chrome finish. Its double edge design provides a very close shave. Its comfortable extra long handle is designed for a non-slip grip and works we… |
|
|
Merkur Long Handled Double Edge Safety Razor #180 with 10 Double Edge Platinum Blades ###############################################################################################################################################################################################################################################################… |
|
|
Sunglass Eyeglass Repair Kit DELUXE set $6.90 This handy kit has nose pads, assorted screws and unique screwdriver – both phillips head and flat head styles needed to complete your repair. A necessary item for any household with glasses! Comes in plastic case (color of case may vary). Contents may shift during shipment. PLEASE NOTE: kit features many screws with out slots -plain round heads that fit in the end of the screwdriver so no matchin… |
|
|
Tools for iPhone and most of phone $0.01 TOOL FOR MOBILE BLACKBERRY PHONES, ETC. T6 T5 SCREW DRIVERS + 2 PLASTIC OPENERS, GOOD FOR MOST MOBILE PHONES BRAND NEW… |
|
|
Complete replacement kit for iphone 4 (Pre-assembled)includes (white) front glass and Digitizer + LCD Assembly + white home button +Custom Iphone 4 screw & washer set + 7 in 1 iphone tool kit + iphone 4 Adhesive + iPhone 4 front & Back screen protector set + Exclusive WizCrafter Microfiber Cloth (AT&T IPHONE 4 ONLY) $58.95 Complete replacement kit for iphone 4 (Pre-assembled)includes (white) front glass and Digitizer + LCD Assembly + white home button +Custom Iphone 4 screw & washer set + 7 in 1 iphone tool kit + iphone 4 Adhesive + iPhone 4 front & Back screen protector set + Exclusive WizCrafter Microfiber Cloth (AT&T IPHONE 4 ONLY)… |
|
|
8pc T6 T5 Opener Screwdriver Tool Kit for Opening BlackBerry Phones PDA MP3 Palm Treo Pocket PC Laptop Blackberry universal cell phone repair tool (HEAVY DUTY) $6.99 8pc T6 T5 Opener Screwdriver Tool Kit for Opening BlackBerry Phones PDA MP3 Palm Treo Pocket PC Laptop Blackberry universal cell phone repair tool… |
|
|
Vietnamese coffee filter set $2.90 Preparing delicious Vietnamese coffee is quick, easy and doesn’t require much clean-up afterward. The coffee filter is stainless steel and there are three parts (filter, screw-on damper, and lid). Simply place the filter on top of a cup, so it looks like a hat. Add 2-3 teaspoons of coffee to the filter, then screw on the damper so it’s snug (not tight). Shake the filter a bit to settle the coffee…. |